Showing results: 166 - 180 of 458 items found.
-
Hilo Test
The ESD Simulators ESD suitable for performing EMC tests of systems and equipment according to the standards IEC / EN 61000-4-2 and ISO / TR 10605. It can far beyond the standard boundaries higher test levels are adjusted. Depending on the device under test and the test setup are two test method shall be: Air discharge (AIR) and contact discharge (CON).
-
PSE Instruments GmbH
This test system is designed to measure the heat transfer during the test of heat pumps and chillers with an integrated pump. The thermal energy is measured with a Coriolis mass flow sensor and two temperature sensors which can be positioned at the inlet and outlet of the test object. Additionally a pressure sensor measures the pressure drop of the heat exchanger of the object under test.
-
Bloomy Controls, Inc.
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
MTB-3200 -
The Eastern Specialty Company
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
AMX 270 -
Guide Technology, Inc.
The AMX 270 "CTIA" architecture improves accuracy by bringing 32 channels of critical front-end input circuitry of GuideTech's Femto Continuous Time Interval Analyzer (CTIA) systems up close to the device under test.
-
TC.ACS -
Regatron AG
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
CI Systems Inc.
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
2650 -
DIT-MCO International
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
C&S group GmbH
According to german Duden conformance means ‘in agreement, accordant’ (from Late Latin conformitas – similarity). Any check on compliance of a test object with its specification can therefore be regarded as a conformance test. A conformance test has become established in the field of networked systems. In networked systems components from different manufacturers work together and only error-free communication under all conditions enables such interoperability.
-
LB302 -
Computer Gesteuerte Systeme GmbH
The LB302 test system is the most used midsize range version of the LB-300 series. It is designed for development as well as for production. The ‘device under test’ (DUT) is connected with a G12 receiver (Virginia Panel Company), which has a high number of possible contacting and a low transition resistance.
-
BurnIn64 -
7Byte Computers
Burnin64 is a burn-in tool designed for AMD64 architecture to test the major components of computer under Windows For 64-bit Extended Systems(x86-64 platform) environment. It is specifically designed to test CPU(s), Motherboard, Memory and Hard drive(s) with the new features of x86-64 architecture in mind.
-
CRMS -
Ultra-Tech Enterprises, Inc.,
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
In-Phase Technologies, Inc.
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
Copernicus Technology Ltd
This family of testers is available as the portable VIFD™ tester (previously called the Ncompass-Voyager) with 128, 256 or 512 test points, and it is available as a 19” rack-mount system – the IFD & Isolation System (IFDIS™) – with thousands of test points. Testers are available from Copernicus Technology for purchase or lease. Alternatively we can provide the full test service for you and we also provide all the corresponding test accessories listed under the Test Equipment menu button.
-
YAV90PIN -
6TL Engineering
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
